Skip to main content

Oscillator Controller for 8bit PIC Microcontrollers

This is oscillator controller for 8bit PIC microcontrollers which is specifically design to debug MCUs and related circuits by without using ICD unit.

This unit consists with low speed oscillator and cycle counter with automatic hold. In current version, oscillator is capable to run in 2 frequency modes and it can count up to 4096 cycles in each run. The number of frequency modes can be extend by adding more capacitors and the upper limit of cycle counter can be increase by adding more 12bit counters (and related circuitries) to the system.

Oscillator waveform in low frequency mode

In current version oscillator can be run in either 66 Hz ~ 70 Hz or 666 Hz ~ 670 Hz (aprox.). This frequency can be adjusted by changing the value of C1 or C2 capacitors (e.g: 0.1MFD can generate 6.39 kHz output signal) OR by replacing R1 with some suitable variable resistor.

In project package we include sample PIC16F84A based project to test with this system. The recommended test attachment is illustrated in below:

Recommended test attachment for PIC16F84A test code

This is open source hardware project and it is licensed under Creative Commons Attribution 4.0 International License. The complete project package is available to download at google drive.

Comments

Popular posts from this blog

CD2003 - yet another simple FM radio receiver

In the last few days, we are looking for some simple FM radio receiver to integrate into one of our ongoing projects. For that, we try several FM radio receiver ICs including TDA7000, CD2003/TA2003/TA8164, CXA1019, and KA22429. Out of all those chips we select CD2003 (or TA2003/TA8164) based receiver for our project because of its simplicity and outstanding performance. Except to CD2003, Sony CXA1019 also perform well but we drop it because of its higher component count. We design our receiver based on Toshiba TA2003 datasheet and later we try TA8164 and CD2003 with the same circuit. Either CD2003 or TA8164 can directly replace TA2003 IC, and as per our observations, TA8164 gives excellent results out of those 3 chips. A prototype version of CD2003 FM radio receiver The PCB design and schematic which we used in our prototype project are available to download at google drive (including pin-outs of crystal filters and inductors ). Except for CD2003 IC, this receiver consist

Arduino superheterodyne receiver

In this project, we extend the shortwave superheterodyne receiver we developed a few years ago . Like the previous design, this receiver operates on the traditional superheterodyne principle.  In this upgrade, we enhanced the local oscillator with Si5351 clock generator module and Arduino control circuit. Compared to the old design, this new receiver uses an improved version of an intermediate frequency amplifier with 3 I.F transformers. In this new design, we divide this receiver into several blocks, which include, mixer with a detector, a local oscillator, and an I.F amplifier. The I.F amplifier builds into one PCB. The filter stage, mixer, and detector stages place in another PCB. Prototype version of 455kHz I.F amplifier. In this prototype build, the Si5351 clock generator drives using an Arduino Uno board. With the given sketch, the user can tune and switch the shortwave meter bands using a rotary encoder. The supplied sketch support clock generation from 5205kHz (tuner frequ

Calculator for audio output transformers

Audio output transformers are heavily used in a vacuum tube and some (older) transistor base audio power amplifiers, but these days output transformer are quite hard to find and expensive item. For homebrew projects, the best option is to construct those transformers by ourselves and this script helps to calculate winding parameters for those transformers. This " AF output transformer calculator " script is written using Python and it works with most of the commonly available Python interpreters . The script is available to download at google drive under the terms of GNU General Public License version 3.0 . Homebrewed 25k: 4 output transformer Once supplied the input parameters this script provides a winding ratio, the number of turns required for primary and secondary winding and required copper wire gauges for both primary and secondary windings, etc. We construct several AF output transformers based on results of this script, which including transformers for M